HIS H435H512HDP Guide de l'utilisateur

ATI Radeon HD 4300 SeriesUser GuidePart Number: 137-41588-10 Rev B

4. Remove any existing graphics cards from the computer.Warning:Some graphics cards can get hot while operating. Wait approximatelyfive minutes after

10. Turn on the monitor and then the computer.The computer should start normally and the software must be installed next.Installing the ATI Catalyst™

Display ConfigurationThis section describes how to configure the display and lists the available displayconnections.Configure the Display (Optional)If

f. Click OK.ConnectionsThe following figure shows the possible connection types on the ATI Radeongraphics card. Available connections may vary between

Adapter DescriptionDVI-to-VGADVI-to-HDMI™DVI-to-YPrPb (for a component cable connection to a LCD or plasma TV)7-pin S-Video cable for video signals7-p

Table 1–1 Display ConfigurationsDisplay ConnectionsCRT analog display•VGA connection•DVI-I-to-VGA adapterLCD display•DVI-I connection and DVI cable•

10 InstallationATI Radeon HD 4300 Series © 2008 Advanced Micro Devices, Inc.

Chapter 2ATI CrossFireX™ TechnologyATI CrossFireX IntroductionATI CrossFireX technology harnesses two or more GPUs (graphics processingunits) to be u

2. Unplug the computer power cord and disconnect the monitor cable fromthe back panel of the computer.Caution:To avoid possible damage to the motherbo

Figure 2–1 ATI CrossFireX Installation7. Fasten the graphics cards securely to the back panel.8. Make sure the cables are not interfering with anyth

© 2008 Advanced Micro Devices Inc. All rights reserved.The contents of this document are provided in connection with Advanced Micro Devices, Inc. (“AM

3. Select the Enable CrossFire™ check box.4. If your system has more than two ATI CrossFireX-capable graphics cards,the dialog appears where you must

Chapter 3ReferenceThe following section offers troubleshooting tips and provides customer care,warranty, and compliance information.System Requiremen

•A second ATI CrossFireX graphics card compatible with the ATI Radeon HD4300 Series. (In most cases, a third card and fourth card may be installed, if

Table 3–1 ATI Catalyst Control Center Access RoutesAccess Route InstructionsWindows Desktop 1. Right-click anywhere on the desktop.2. From the short

TroubleshootingGraphics Card Installation TroubleshootingFor more advanced troubleshooting information, contact AMD Customer Carefor ATI products at a

Troubleshooting ATI CrossFireXThe following are suggested solutions for common ATI CrossFireXtroubleshooting issues.Change Motherboard BIOS SettingsSo

•Check that the interconnect cable is installed correctly.•Close all running 3D applications.•Re-install the ATI Catalyst Control Center and drivers.S

The entire display is not visible.If the component input device supports it, try 720p mode.The display appears tilted.Consult the HDTV documentation.T

result of the product, whether your product contains a defect, and whether yourproduct is under warranty.•AMD Customer Care is unable to assist with r

•Increase the separation between the equipment and receiver.•Connect the equipment to an outlet on a circuit different from that to whichthe receiver

Important Safety InstructionsNote: This product is for use only with compatible UL-listed personal computers thathave installation instructions detail

To meet UL safety requirements, the computer’s maximum room temperatureshould not exceed 40 °C.Waste Electrical and Electronic Equipment (WEEE) Direct

BSMI Certification InformationBSMI Certification Information 25© 2008 Advanced Micro Devices, Inc. ATI Radeon HD 4300 Series

26 ReferenceATI Radeon HD 4300 Series © 2008 Advanced Micro Devices, Inc.

Note to CATV System InstallerThis reminder is provided to call the CATV systems installer’s attention to Section 820-40of the NEC, which provides guid

ContentsInstallation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Installation Overview

Waste Electrical and Electronic Equipment (WEEE) Directive Compliance . . . . . . . . . . . . . . . . . . .24VCCI Class B ITE Compl

Chapter 1InstallationFor support, you will need to record the serial number and the part number forthe card before installation.Installation Overview

Record the Serial and Part NumbersWrite down the serial number and part number before installing. The serialnumber and 102 part number on the graphics

Uninstalling the Old Driver (Windows Vista®)Follow these steps to uninstall the existing graphics card driver in preparationfor installation of a new